See Availability

Here in the next paragraph you will find a lot of wonderful data when it comes to A Step-by-Step Guide to Installing a Bathtub.

Mounting a tub isn't specifically brain surgery, however it does call for strong plumbing, carpentry, and occasionally, tiling abilities. Replacing an old bath tub with a brand-new one is also a moderately difficult job. If the old tub is conveniently easily accessible, the project can move rapidly; if you have to open up a wall to get rid of the old tub as well as place the new tub, the job is a lot harder. In either case, the job is within a house handyman's abilities, although you will certainly require a helper to leave the old bathtub and also set in the new one. Make certain you have qualified yourself for the job as well as fit trying it. Rather than employing a service provider to take over a halfway-completed task, it is far better to consider employing one before you begin. Chances are you may need a professional plumber to make tube links.
This short article will help you install a brand-new bath tub in your washroom if you have actually currently gotten a new tub and also do not need to change the arrangement of your previous water supply pipelines.
Your tools and product checklist need to make up the following:

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipe Caps


 

Planning for the Installment

To start with, the supporting structure provided with the bath must be fitted (if required) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is necessary to make certain that if the faucet features a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets device to stop pressure on the bath tub.
Fit the versatile faucet ports to the bottom of the two taps using 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you use all of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath must currently prepare to be suited its final setting.

Removing Old Taps

If you need to replace old taps with new ones as a part of your setup, then the first thing you must do is detach the water. After doing so, activate the taps to drain any water remaining in the system. The procedure of getting rid of the existing faucets can be rather troublesome due to the limited gain access to that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the taps. Have a cloth prepared for the staying water that will certainly come from the pipelines. When the supply pipelines have been gotten rid of, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single taps from turning during this process. As soon as the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing compound.
Prior to going on to fit the brand-new taps, compare the pipe connections on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.

Installing the Bathtub

Utilizing the two wood boards under its feet, put the bath tub in the called for position. The wood boards are practical in evenly spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto four little points.
The following goal is to guarantee that the bath tub is leveled all round. This can be achieved by examining the level and changing the feet on the bathtub up until the level reviews level.
To mount taps, fit the bottom of the furthest adaptable faucet connector to the suitable supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Activate the water and also inspect all joints and also brand-new pipework for leakages and tighten them if required. Fill the bath tub as well as also check the overflow outlet as well as the typical electrical outlet for leakages.
Ultimately, take care of the bathroom paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bath tub needs to wait until the tub has actually been utilized a minimum of once as this will resolve it right into its final placement.

Suitable New Touches

If the tails of the brand-new taps are plastic, after that you will certainly need a plastic connector to prevent damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end supplies a link to the existent supply pipelines.
If you require to fit a monobloc, then you will require lowering couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the tap in the placing hole in the bath/basin guaranteeing that the washing machines remain in area between the tap and also the sink. Protect the faucet in position with the maker provided backnut. When the faucet is firmly in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with regular tap ports. The previous type needs to be linked to the faucet finishes initially, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.

Tiling Around the Bath tub

In the location where the bath satisfies the floor tile, it is essential to seal the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to split an inflexible seal, causing the water to pass through the wall surface between the bathroom and the tiling, resulting in issues with moisture and also possible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your fixtures and fittings. They are marketed in tubes and cartridges, and are capable of securing voids up to a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to always fill the bathtub with water before securing, to enable the movement experienced when the bathtub is in usage. The sealant can fracture relatively early if you do not think about this motion prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally quickly readily available on the market. It is a good idea to fit the floor tiles making use of water-resistant or water resistant glue as well as grout.

A Step-by-Step Guide to Installing a Bathtub

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

 

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

 

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

Remove the Existing Bathtub

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

 

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

Choose the Right Bathtub

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

Install the Plumbing and Ledger Board

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

 

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

Install the Bathtub

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

 

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

 

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

Hook up the Plumbing

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

Install the Bathtub Surround

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

 

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

 

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

 

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

I hope you enjoyed reading our piece on How to Install a Bathtub Yourself. Thanks a ton for taking time to read through our blog. Sharing is caring. Helping others is fun. Many thanks for your time. Come back soon.

Schedule Today